back to top

hunan neptune pump

Sharing Operational Experience Is Critical in RO Plant Desig

Source:未知|Popularity:0|release date:2020-04-21 10:20:34
Sharing Operational Experience Is Critical in RO Plant Design
The future of desalination will require a combination of experienced-based design and environmentally friendly technologies.
Today’s reverse osmosis (RO) plant design is based on diverse technological knowledge and, just as importantly, on operational experience, which can be a valuable asset for design teams. For desalination plants, it is important to explore a methodology for bridging between operation and maintenance (O&M) experience and design, while finding the process design of the future.
O&M teams can gain operational experience through daily work of performance monitoring and overcoming challenges. Typical objectives of the operation team include improving plant performance, correcting malfunctions, boosting compliance with new regulations and reducing operational costs.
Methods of harnessing operational experience and turning it into valuable design knowledge for desalination plants include:
periodic meetings focused on sharing knowledge between O&M companies and design engineers
on-site piloting, which allows technical interaction between the O&M team and the design engineers
monthly reports issued by the O&M managers
providing technical and process support to the operation team as required
inviting lead technologists and operation managers to participate in design review meetings
Taking operational experience into consideration does not mean that the RO plant is overplanned. Sometimes a small investment can make a big difference and lead to better results for the plant.
Operational experience can help prevent execution and startup difficulties. The following shows real-world examples of incorporating operational experience into design knowledge.

Optimization to Reduce O&M Cost

The design team should learn the RO plant’s behavior from the O&M personnel and optimize the design accordingly. For example, the chemical consumption can be reduced through improvements and optimizations performed during O&M.
At the Ashkelon Desalination Plant in Israel, the second pass chemical consumption of caustic soda and sulfuric acid were optimized through day-to-day monitoring of the performance parameters such as actual boron rejection, membrane-feed pressure and normalized flow. Ferric chloride consumption was optimized through monitoring of pretreatment performances and by using improved control methods.
Another parameter to improve is the plant’s specific energy consumption. Although specific energy consumption should increase as the RO membranes age, the O&M team at Ashkelon successfully maintains guaranteed energy consumption and, in some cases, improves the plant’s specific energy. In this case, the O&M teams reduced energy consumption by replacing a valve internal part, which created a high pressure drop, and by developing methods and procedures for maintaining RO membranes’ performance by rotation of the membranes with the pressure vessel. The real behavior of the plant, including actual pressure drops and energy consumption, can help optimize future designs.

Equipment Failure

One method of improving design is by studying equipment failures together with the O&M team and providing technical support until a solution is found. During the first operation period in the Hadera Desalination Plant in Israel, the media filter’s flap valves suffered from leakage. A new mechanism based on hydraulic pistons was developed, including reinforcement of the shafts and improvement of the rubber sealing.
The hydraulic mechanism was first piloted and then implemented successfully in full scale.
The experience from Hadera and the upgraded solution has been used in some later designed RO plants, such as in the Vasilikos Desalination Plant in Cyprus and Carlsbad Desalination Plant in Southern California.

Optimization of Control & Automatic Sequencing

An example of how optimizing control and automatic sequencing can lead to design upgrades involved leakage from high-pressure (HP) valves isolating the RO train identified in the Hadera plant.
Following a thorough investigation, the O&M team improved the startup and pressurization sequence so the pressurization occurred in a gradual manner, preventing sheer forces on the isolation valve’s Teflon sleeve. This modification proved successful and the experience was transferred to some other plants working with pressure center.

Construction Materials

The O&M team gains significant experience and knowledge of what material is resistant and what should not be used. The chemical line insulation and heating provision were added for chemicals with a high freezing point (such as NaOH lines) in the Ashkelon plant.
The sulfuric acid injection assemblies, which suffered from many leaks because of the exothermic conditions existing in the injection point, were replaced with a Teflon-coated steel type. This robust solution was then added to future designs.
Additional coatings for concrete, steel and pumps were implemented by the O&M teams. The team, with the support of the design team, implemented a cathode protection system for the metal pipes and pumps. Some of these lessons, already learned during the design stage, will cost less in the overall plant life cycle.

Adoption of Add-On Systems

The O&M team may adopt or install additional systems or solutions as a response to maintenance problems. The design team can study the problem and the implemented solution and, in relevant cases, it can be added into future designs.
For example, areas with high-suspended solids load are typically known as high-maintenance areas and therefore not favorable for the O&M teams. Specifically, limestone suspended solids started to settle and accumulate in a backwash channel. For this case, the O&M team introduced a simple nozzle system for mixing and preventing of the massive settling. In later design, means of preventing settling in high total suspended solids (TSS) areas have been considered.
An additional example for an add-on system is when Ashkelon’s O&M team intended to reduce the cartridge filter replacement rate by cleaning used cartridges and putting them back in operation. At first, the team used a pilot, after which a cartridge clean-in-place (CIP) system was added into the full-scale plant. Later, a cartridge CIP system was incorporated into the Hadera plant design.
In this and other such cases, it is important not to automatically adopt every modification. In some cases a solution can be suitable only for the specific site. In the case of a cartridge filters CIP system, introducing the system and performing the cleaning should be evaluated on a case-by-case basis because it may not always be cost-effective (depending on the expected replacement rate and the cost of available cartridge filters).

System Optimization

When the O&M team encounters a problem, it is important to not finalize any design decisions too early. For example, the sludge treatment centrifuges in Israel’s Sorek, the world’s largest seawater reverse osmosis (SWRO) desalination plant, were replaced by a filter press because of frequent failures. However, the same centrifuges are used and perform well in the same application at the Carlsbad plant, which is the largest desalination plant in the Western Hemisphere.
During the first period of operation in Hadera, the team encountered operational problems with the limewater preparation system, including unstable control, high maintenance and low performance. In this case, the operation team worked on stabilizing the system, improving and optimizing its performance.
These examples demonstrate that if adequate time, resources and technical support are provided, stabilization is reached or a solution can be found.
Using the O&M to learn the RO plant’s behavior and optimize plant design accordingly is of paramount importance. The future of desalination will require a combination of experienced-based design and environmentally friendly technologies.